T BAILEY, INC., founded in 1991, is a diversified heavy-civil/industrial general contractor. Our expertise is construction - earth/utility/concrete work, tank and steel erection and heavy plate/structural fabrication with an emphasis on storage tanks and wind turbine towers. Our vast experience in aboveground, field-erected fuel and water tank projects has established T BAILEY, INC. as one of the Northwest leaders in safety, quality control, and project management.

Here is a partial list of the projects that T BAILEY, INC. has completed.

(click on anything below to jump to that section of the page)

Construction Fuel Tanks Water Tanks Pipe Underground Utilities Foundations Misc. Projects

Fabrication Tanks Pipe Casing/Caissons Plate/Ductwork Wind Towers

Construction - Fuel Tanks	Back to Top
Anchorage International Airport Fueling Facility   Location: Anchorage, Alaska   Client:  Anchorage International Airport Fabrication and construction of (3) 4.2 million gallon, (1) 225,000 gallon, welded steel API 650 fuel storage tanks, and (1) 225,000 gallon welded steel water storage tank.
Fabrication - Tanks	Back to Top
Upgrade POL System   Location: Tin City, Alaska   Client:  Alaska District U.S. Army Corps of Engineers Fabrication and construction of 9 each 145,000 liter UL 142 rated horizontal diked fuel tanks and associated fuel piping system.
Construction - Water Tanks	Back to Top
1 MG Sedgewick Reservoir   Location: Port Orchard, Washington   Client:  City of Port Orchard Construct a new 1,000,000 gallon water reservoir and foundation.  Project included fabrication/erection/painting of the reservoir, sitework, drainage and water utilities.
Muckleshoot Standpipe   Location: Muckleshoot Indian Reservation in Auburn, Washington   Client:  Department of Health & Human Services Portland Area Indian Health Services Fabrication and construction of 915,000 gallon welded steel water storage tank.
Fabrication - Pipes	Back to Top
Tumalo Irrigation District Siphon   Location: Bend, Oregon   Client:  Tumalo Irrigation District Fabrication of 1,200 lf of AWWA C200 92” OD and 84” OD welded steel irrigation siphon including inlet and outlet structures.
Windy Point Pipe Bridge   Location: Yakima, Washington   Client:  Yakima – Tieton Irrigation District   Fabrication and installation of 104 lf of 102” diameter 3/8” wall welded steel AWWA C200 irrigation water pipe bridge, including concrete abutments, and sitework.
Construction - Pipe	Back to Top
Tumalo Irrigation District Siphon   Location: Bend, Oregon   Client:  Tumalo Irrigation District   Construction of 1,200 lf of AWWA C200 92” OD and 84” OD welded steel irrigation siphon including inlet and outlet structures.
Peter Pan Seafoods Fuel Farm Upgrade   Location: King Cove, Alaska   Client:  Peter Pan Seafoods   Construct a new 15,000 sq ft containment dike, relocate 2 each 300,000 gallon API 650 tanks to a new tank farm, process piping and equipment, pump house, above and underground fuel lines to dock receiving/issuing station.
Upgrade POL System   Location: Tin City, Alaska   Client:  Alaska District U.S. Army Corps of Engineers Fabrication and construction of 9 each 145,000 liter UL 142 rated horizontal diked fuel tanks and associated fuel piping system.
Fabrication - Casing	Back to Top
SAR Rapid Transit 2000   Location: Vancouver, B.C. CANADA   Client:  AGRA Foundations Fabrication of Caissons ranging from ½” to ¾” thick and 100”, 108”, 120”, and 128” in diameter.  Approximately 10,000 lf of Caissons were produced for this project.
Construction - UG Utilities	Back to Top
Reservoir Improvements and Seismic Upgrades   Location: Lynnwood, Washington   Client:  Alderwood Water District   Project included seismic upgrades of two existing water reservoirs, fabrication/erection of 2 additional water reservoirs, foundations, and associated sitework. Underground utilities included ductile iron piping and associated valves.
Fabrication - Plate/Ductwork	Back to Top
Keahole Combined Cycle Project   Location: Keahole Power Plant, Hawaii   Client:  Hawaiian Electric Co. Fabrication and construction of stainless steel lined duct work and stack for a local power plant.
Centralia Flue Gas Desulfurization Project   Location: Centralia, Washington   Client:  ABB Alstrom Power and Stone & Webster Fabricate, site erect, and insulate exhaust ductwork.  Fabricate, site erect, and paint seven tanks.
Construction - Foundations	Back to Top
5.25 MG Redmond Ridge Tank #2   Location: Redmond, Washington   Client:  Quadrant Corporation   Construction of a new 5,250,000 gallon standpipe, foundation, associated site earthwork/grading, utilities, electrical, cathodic protection, etc. Foundation was accomplished in one continuous pour consisting of 7 lifts and approximately 1300 cubic yards of concrete to form a 100.5’ OD x 60’ ID ring footing for the standpipe containing 93 anchor bolts and approximately 180,000 lbs. of steel reinforcement.
Boulevard Road Reservoir   Location: Olympia, Washington   Client:  City of Olympia   Project included demolition/removal of an existing standpipe and construction of a new 2,560,000 gallon water reservoir, foundation, associated site earthwork/grading, utilities, electrical, telemetry, etc. Foundation consisted of approximately 1000 cubic yards of concrete to form a 87’ diameter mat foundation for the reservoir containing 76 anchor bolts and approximately 144,000 lbs. of steel reinforcement.
Fabrication - Wind Towers	Back to Top
Condon, OR Wind Tower Project   Location: Condon, Oregon   Client:  Seawest Wind Power, Inc. Fabrication, painting, and delivery of thirty-one 60 meter, 600KW conical towers.  The turbine manufacturer is Mitsubishi Heavy Industries LTD.
Construction - Misc.	Back to Top
Fire Fighting Training Pit   Location: Whidbey Island Naval Air Station, Oak Harbor, WA   Client:  Department of Navy Fabrication and construction of a fire fighting training facility including:  sitework, structural steel mock-up, high temperature resistant concrete pads, control building, jet fuel fire simulation system, electrical.
HRSG Stack Installation / Coyote Springs II   Location: Boardman, Oregon   Client:  Coyote Springs II Power Project for Enron/Avista Equipment, labor, and consumables for the field installation/erection of (one) single wall 18” ID x 210’ tall stack.  Wall thickness ranging from 5/8” – 3/8”.